Why Would My Ice Maker Stop Working Then Start Again
Having ice ready whenever yous desire or need it is a luxury nosotros all take for granted, that is, until you reach to get some water ice from the freezer and there is none.
Ice makers fail. Information technology's an unfortunate reality of owning a refrigerator with an ice maker.
On the bright side, ice makers are likewise relatively simple machines that, for the virtually part, all operate the same way. And y'all may be able diagnose and repair a faulty ice maker yourself before forking over cash for an expensive service phone call.
Here'due south how to fix some common ice maker problems.
When ice is not ejecting
If you discover water ice inside the ice mold, it means your ice maker is receiving water and the problem likely isn't with the water supply. Instead, information technology's about likely a mechanical or electrical trouble.
Cause: When moving things around in the freezer, it's non uncommon to accidentally nudge the control arm into the off position, which halts production of ice.
Ready: This is an easy fix. Locate the metallic control arm and motility it to the down or on position.
Cause: If the command arm is in the on (downwardly) position and the mold is filled with ice, the problem likely lies with the motor, gearbox or electric connexion.
Ready: Start by making sure all electric connections are properly seated. Slide the refrigerator out from the wall, plow off the water supply valve and disconnect it from power. Locate the quick release plug on the dorsum wall within the freezer. Unplug the connection information technology and reconnect it to ensure it'south fully connected.
Manually remove whatever remaining water ice from the mold past adding some water and letting information technology sit for a infinitesimal. The ice volition begin to melt and should be easier to remove.
Restore power to the refrigerator and lift the control arm to the off position. Lower the control arm back down and expect for approximately 10 seconds for the solenoid to engage and fill the mold with water.
Wait three to four hours for the water ice to freeze and see if the ice now ejects. If not, it'southward likely that you will need to supplant the motor or gearbox.
When it'south non making water ice at all
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it'due south typically indicative of a clog somewhere along the supply line.
Cause: A common crusade for a clog is frozen h2o in the line.
Fix: To repair a frozen line, slide the refrigerator and unplug information technology. Locate the shut-off valve, typically underneath the sink or backside the fridge. Turn the valve to the closed or off position. Make full a turkey baster with warm water and cascade the water over the water line. Alternatively, you tin can defrost the h2o line with a pilus dryer or by letting the refrigerator sit down unplugged for upward of ii hours.
Restore ability to the refrigerator and listen for the water supply to fill the ice mold.
If the clog is anything only translucent, consult with a professional for help removing the clog.
Crusade: There is also a possibility that the water filter for the ice maker is clogged.
Fix: Locate and replace the water filter. Filters for water ice makers are typically located inside the refrigerator (to continue them from freezing).
When cubes are besides big or pocket-size
Cause: If the ice crescents are too big or there is no clog and they're still too small, chances are, the ice maker merely needs a little adjustment.
Gear up: To conform how much water the ice mold is filled with each bike, first remove the cover from the ice maker. Information technology'due south the white plate on the frontmost part of the water ice maker assembly and information technology should pull off rather easily. If you're having difficulty removing it, use a flat caput screwdriver to gently pry it away from the housing.
Under the cover, y'all should see a screw and spring assembly, along with a plus and minus indicator. This controls the dosing for water. Screw in (toward the minus symbol) to decrease the amount of water per dose and out (toward the plus) to increase the amount of water per dose.
Source: https://www.cnet.com/home/kitchen-and-household/what-to-do-when-your-ice-maker-stops-making-ice/
Post a Comment for "Why Would My Ice Maker Stop Working Then Start Again"